SUBARU SELECT MONITOR
Engine (Diagnostics)
6. Subaru Select Monitor
S068503
5) Turn ignition switch to ON (engine OFF) and Subaru Select Monitor switch to ON.
A: OPERATION
S068503A16
for_01_21-352.jpg
1. HOW TO USE SUBARU SELECT
MONITOR S068503A1601
1) Prepare Subaru Select Monitor kit.
for_01_21-353.jpg
6) Using Subaru Select Monitor, call up diagnostic trouble code(s) and various data, then record them.
2. READ DIAGNOSTIC TROUBLE CODE
2)  Connect diagnosis cable to Subaru Select Monitor.
3)   Insert cartridge into Subaru Select Monitor.
(DTC) FOR ENGINE.
S068503A1602
Refer to Read Diagnostic Trouble Code for infor­mation about how to indicate DTC. <Ref. to EN(SOHCw/oOBD)-27 Read Diagnostic Trouble Code.>
for_01_21-354.jpg
4) Connect Subaru Select Monitor to data link
connector.
(1) Data link connector located in the lower por­tion of the instrument panel (on the driver's side).
for_01_21-355.jpg
(2) Connect diagnosis cable to data link con­nector.
CAUTION:
Do not connect scan tools except for Subaru
Select Monitor.
EN(SOHCw/oOBD)-24
SUBARU SELECT MONITOR
Engine (Diagnostics)
3. READ CURRENT DATA SHOWN ON DISPLAY.
S068503A1603
1)  On the <§Main Menu> display screen, select the {2. Each System Check} and press the [YES] key.
2)  On the ^System Selection Menu> display screen, select the {Engine Control System} and press the [YES] key.
3)   Press the [YES] key after displayed the information of engine type.
4)  On the ^Engine Diagnosis^ display screen, select the {1. Current Data Display & Save} and press the [YES] key.
5)  On the <§Data Display Menu> display screen, select the {1. 12 Data Display} and press the [YES] key.
6)   Using the scroll key, move the display screen up or down until the desired data is shown. • A list of the support data is shown in the following table.
Contents
Unit of measure
Battery voltage
V
Vehicle speed signal
km/h or MPH
Engine speed signal
rpm
Engine coolant temperature signal
°C or °F
Ignition timing signal
deg
Throttle position signal
%
Throttle position signal
V
Injection pulse width
ms
Idle air control signal
%
Engine load data
%
Front oxygen sensor output signal
V
A/F correction coefficient
%
Knock sensor signal
deg
CO resistor
V
Intake manifold absolute/relative pressure signal
mmHg or kPa or inHg
Intake air temperature signal
°Cor°F
Canister purge control solenoid valve duty ratio
%
Idle air control solenoid valve current
mA
Ignition switch signal
ON or OFF
Test mode connector signal
ON or OFF
Neutral position switch signal
ON or OFF
Air conditioning switch signal
ON or OFF
Air conditioning relay signal
ON or OFF
Radiator main fan relay signal
ON or OFF
Fuel pump relay signal
ON or OFF
Knocking signal
ON or OFF
Radiator sub fan relay signal
ON or OFF
Engine torque control signal
ON or OFF
Front oxygen sensor rich signal
ON or OFF
Crankshaft position sensor signal
ON or OFF
Electrical load signal
ON or OFF
Read memory connector signal
ON or OFF
Power steering pressure signal
ON or OFF
AT vehicle ID signal
ON or OFF
Idle switch
ON or OFF
Canister purge control solenoid valve
ON or OFF
Torque permission signal
ON or OFF
NOTE:
For detailed operation procedure, refer to the SUBARU SELECT MONITOR OPERATION MANUAL.
EN(SOHCw/oOBD)-25
SUBARU SELECT MONITOR
Engine (Diagnostics)
4. LED OPERATION MODE FOR ENGINE S068503A1604
Contents
Message
LED "ON" requirements
Ignition switch signal
ON or OFF
When ignition switch is turned ON.
Test mode connector signal
ON or OFF
When test mode connector is connected.
Neutral position switch signal
ON or OFF
When neutral position signal is entered.
Air conditioning switch signal
ON or OFF
When air conditioning switch is turned ON.
Air conditioning relay signal
ON or OFF
When air conditioning relay is in function.
Radiator main fan relay signal
ON or OFF
When radiator main fan relay is in function.
Fuel pump relay signal
ON or OFF
When fuel pump relay is in function.
Knocking signal
ON or OFF
When knocking signal is entered.
Radiator sub fan relay signal
ON or OFF
When radiator sub fan relay is in function.
Engine torque control signal
ON or OFF
When engine torque control signal is entered.
Front oxygen sensor rich signal
ON or OFF
When front oxygen sensor mixture ratio is rich.
Crankshaft position sensor signal
ON or OFF
When crankshaft position sensor signal is entered.
Electrical load signal
ON or OFF
When the lighting switch, blower fan switch or rear defog-ger switch is turned ON.
Read memory connector signal
ON or OFF
When read memory connector is connected.
Power steering pressure signal
ON or OFF
When steering wheel is turned.
AT vehicle ID signal
ON or OFF
When AT identification signal is entered.
Idle switch
ON or OFF
When throttle sensor sends signal that throttle opening angle is in idle position.
Canister purge control solenoid valve
ON or OFF
When canister purge control solenoid valve is in function.
Torque permission signal
ON or OFF
When torque permission signal is entered.
NOTE:
For detailed operation procedure,
refer to the SUBARU SELECT MONITOR OPERATION MANUAL.
EN(SOHCw/oOBD)-26