INSPECTION MODE
Engine (Diagnostics)
12. Inspection Mode
S058510
1) Prepare Subaru Select Monitor kit. <Ref. to EN(SOHC)-8, PREPARATION TOOL, General Description.>
A: OPERATION
S058510A16
1. PREPARATION FOR THE INSPECTION
for_01_20-65.jpg
MODE
S058510A1601
Raise the vehicle using a garage jack and place on safety stands or drive the vehicle onto free rollers.
WARNING:
-  Before raising the vehicle, ensure parking brakes are applied.
-  Do not use a pantograph jack in place of a safety stand.
-  Secure a rope or wire to the front and rear towing or tie-down hooks to prevent the lateral runout of front wheels.
-  Do not abruptly depress/release clutch pedal or accelerator pedal during works even when engine is operating at low speeds since this may cause vehicle to jump off free rollers.
-  In order to prevent the vehicle from slipping due to vibration, do not place any wooden blocks or similar items between the safety stands and the vehicle.
-  Since the rear wheels will also rotate, do not place anything near them. Also, make sure that nobody goes in front of the vehicle.
2)  Connect diagnosis cable to Subaru Select Monitor.
3)   Insert cartridge into Subaru Select Monitor. <Ref. to EN(SOHC)-8, PREPARATION TOOL, General Description.>
for_01_20-66.jpg
for_01_20-67.jpg
4) Connect test mode connector (A) at the lower portion of instrument panel (on the driver's side), to the side of the center console box.
for_01_20-68.jpg
2. SUBARU SELECT MONITOR
S058510A1602
After performing diagnostics and clearing the memory, check for any remaining unresolved trouble data.
EN(SOHC)-42
INSPECTION MODE
Engine (Diagnostics)
5) Connect Subaru Select Monitor to data link
connector.
(1) Connect Subaru Select Monitor to data link connector located in the lower portion of the instrument panel (on the driver's side).
NOTE:
-   For detailed operation procedure, refer to the SUBARU SELECT MONITOR OPERATION MANUAL.
-   For detailed concerning diagnostic trouble codes, refer to the List of Diagnostic Trouble Code (DTC). <Ref. to EN(SOHC)-80, List of Diagnostic Trouble Code (DTC).>
-   Release the parking brake.
-  The speed difference between front and rear wheels may light either the ABS warning light, but this indicates no malfunctions. When engine con­trol diagnosis is finished, perform the ABS memory clearance procedure of self-diagnosis system.
for_01_20-69.jpg
3. OBD-II GENERAL SCAN TOOL
S058510A1603
After performing diagnostics and clearing the memory, check for any remaining unresolved trouble data:
1) Connect test mode connector (A) at the lower side of the instrument panel (on the driver's side), to the side of the center console box.
(2) Connect diagnosis cable to data link con­nector.
CAUTION:
Do not connect scan tools except for Subaru
Select Monitor and OBD-II general scan tool.
6) Turn ignition switch to ON (engine OFF) and Subaru Select Monitor switch to ON.
for_01_20-70.jpg
for_01_20-71.jpg
2) Connect the OBD-II general scan tool to its data link connector (A) in the lower portion of the instru­ment panel (on the driver's side).
CAUTION:
Do not connect the scan tools except for
Subaru Select Monitor and OBD-II general scan
tool.
7)  On the <§Main Menu> display screen, select the {2. Each System Check} and press the [YES] key.
8)  On the ^System Selection Menu> display screen, select the {Engine Control System} and press the [YES] key.
9)   Press the [YES] key after displayed the infor­mation of engine type.
10)  On the ^Engine Diagnosis^ display screen, select the {Dealer Check Mode Procedure} and press the [YES] key.
11)  When the "Perform Inspection (Dealer Check) Mode?" is shown on the display screen, press the [YES] key.
12)   Perform subsequent procedures as instructed on the display screen.
- If trouble still remains in the memory, the corre­sponding diagnostic trouble code (DTC) appears on the display screen.
for_01_20-72.jpg
EN(SOHC)-43
INSPECTION MODE
Engine (Diagnostics)
3)  Start the engine.
NOTE:
-   Ensure the selector lever is placed in the "P" position before starting. (AT vehicles)
-   Depress clutch pedal when starting the engine. (MT vehicles)
4)   Using the selector lever or shift lever, turn the "P" position switch and the "N" position switch to ON.
5)   Depress the brake pedal to turn the brake switch ON. (AT vehicles)
6)   Keep engine speed in the 2,500 - 3,000 rpm range for 40 seconds.
NOTE:
On models without tachometer, use the tachom­eter (Secondary pickup type).
7)   Place the selector lever or shift lever in the "D" position (AT vehicles) or "1st" gear (MT vehicles) and drive the vehicle at 5 to 10 km/h (3 to 6 MPH).
NOTE:
-  On AWD vehicles, release the parking brake.
-  The speed difference between front and rear wheels may light the ABS warning light, but this indicates no malfunctions. When engine control diagnosis is finished, perform the ABS memory clearance procedure of self-diagnosis system.
8)   Using the OBD-II general scan tool, check for diagnostic trouble code(s) and record the result(s).
NOTE:
-   For detailed operation procedures, refer to the OBD-II General Scan Tool Instruction Manual.
-   For detailed concerning diagnostic trouble codes, refer to the List of Diagnostic Trouble Code (DTC). <Ref. to EN(SOHC)-80, List of Diagnostic Trouble Code (DTC).>
EN(SOHC)-44