GENERAL DESCRIPTION
Starting/Charging Systems
1. General Description
S179001
S179001E49
A: SPECIFICATIONS
Item
Designation
Starter
Type
Reduction type
Vehicle type
AT vehicles
AT vehicles
Model
M000T83981
M001T86481
Manufacturer
Mitsubishi Electric
Voltage and output
12 V- 1.0 kW
12 V- 1.4 kW
Direction of rotation
Counterclockwise (when observed from pinion)
Number of pinion teeth
8
9
No-load charac­teristics
Voltage
11 V
Current
90 A or less
Rotating speed
2,400 rpm or more
2,400 rpm or more
Load character­istics
Voltage
7.7 V
7.7 V
Current
400 A
400 A
Torque
8.6 N-m (0.88 kgf-m, 6.4 ft-lb) or more
16.0 N-m (1.63 kgf-m, 11.8 ft-lb) or more
Rotating speed
740 rpm or more
740 rpm or more
Lock characteris­tics
Voltage
4 V
3.5 V
Current
940 A or less
940 A or less
Torque
14.7 N-m (1.50 kgf-m, 10.8 ft-lb) or more
28.9 N-m (2.95 kgf-m, 21.3 ft-lb) or more
Generator
Type
Rotating-field three-phase type, Voltage regulator built-in type, with load response control system
Model
A2TB6291
Manufacturer
Mitsubishi Electric
Voltage and output
12 V -75 A
Polarity on ground side
Negative
Rotating direction
Clockwise (when observed from pulley side)
Armature connection
3-phase Y-type
Output current
1,500 rpm - 30 A or more 2,500 rpm - 64 A or more 5,000 rpm - 76 A or more
Regulated voltage
14.1 - 14.8 V [20°C (68°F)]
Battery
Type and capac­ity
For Europe
12 V -48 AH
12 V -52 AH
For Australia
12 V -40 AH
Others
12 V -40 AH
SC-2
GENERAL DESCRIPTION
Starting/Charging Systems
B: COMPONENT
1. STARTER S179001A0501
S179001A05
for_01_19-2.jpg
(1)
Sleeve bearing
(7) Internal gear ASSY
(2)
Front bracket
(8) Shaft ASSY
(3)
Lever set
(9) Gear ASSY
(4)
Magnet switch ASSY
(10) Ball
(5)
Stopper set
(11) Packing
(6)
Over running clutch
(12) Yoke
(13)  Armature
(14)  Brush holder
(15)  Brush
(16)  Sleeve bearing
(17)  Rear bracket
SC-3
GENERAL DESCRIPTION
Starting/Charging Systems
2. GENERATOR
S179001A0502
for_01_19-3.jpg
(1)    Pulley
(2)    Front cover
(3)    Ball bearing
(4)    Bearing retainer
C: CAUTION
(5)    Rotor
(6)    Bearing
(7)    Stator coil
(8)    IC regulator with brush
(9)    Brush
(10)  Rectifier
(11)  Rear cover
(12)  Terminal
S179001A03
removal, installation, disassembly, and replace­ment.
-   Be careful not to burn your hands, because each part in the vehicle is hot after running.
-   Be sure to tighten fasteners including bolts and nuts to the specified torque.
-   Place shop jacks or safety stands at the speci­fied points.
-   Before disconnecting electrical connectors of sensors or units, be sure to disconnect negative terminal from battery.
-  Wear working clothing, including a cap, protec­tive goggles, and protective shoes during opera­tion.
-   Remove contamination including dirt and corro­sion before removal, installation or disassembly.
-   Keep the disassembled parts in order and pro­tect them from dust or dirt.
-   Before removal, installation or disassembly, be sure to clarify the failure. Avoid unnecessary
SC-4