OBD-II GENERAL SCAN TOOL
Engine (Diagnostics)
9. OBD-II General Scan Tool
S088527
3) Using the OBD-II general scan tool, call up diagnostic trouble code(s) and freeze frame data. OBD-II general scan tool functions consist of:
(1)   MODE $01: Current powertrain diagnostic data
(2)   MODE $02: Powertrain freeze frame data
(3)   MODE $03: Emission-related powertrain diagnostic trouble codes
(4)   MODE $04: Clear/Reset emission-related diagnostic information
Read out data according to repair procedures. (For detailed operation procedures, refer to the OBD-II General Scan Tool Operation Manual.)
NOTE:
For details concerning diagnostic trouble codes, refer to the List of Diagnostic Trouble Code (DTC). <Ref. to EN(DOHC TURBO)-82, List of Diagnostic Trouble Code (DTC).>
A: OPERATION
S088527A16
1. HOW TO USE OBD-II GENERAL SCAN
TOOL
S088527A1601
1)   Prepare a general scan tool (OBD-II general scan tool) required by SAE ? 978.
2)  Open the cover and connect the OBD-II general scan tool to the data link connector (A) located in the lower portion of the instrument panel (on the driver's side).
for_01_24-65.jpg
2. MODE $01 (CURRENT POWERTRAIN DIAGNOSTIC DATA)
S088527A1602
Refers to data denoting the current operating condition of analog input/output, digital input/output and/or
the powertrain system.
A list of the support data and PID (Parameter Identification) codes are shown in the following table.
PID
Data
Unit of measure
01
Number of emission-related powertrain trouble codes and MIL status
ON/OFF
03
Fuel system control status
04
Calculated engine load value
%
05
Engine coolant temperature
°C
06
Short term fuel trim
%
07
Long term fuel trim
%
0B
Intake manifold absolute pressure
kPa
??
Engine revolution
rpm
0D
Vehicle speed
km/h
0E
Ignition timing advance
°
0F
Intake air temperature
°C
10
Air flow rate from pressure sensor
g/sec
11
Throttle valve opening angle
%
13
Check whether oxygen sensor is installed.
15
Oxygen sensor output voltage and short term fuel trim associated with oxygen sensor—bank 2
V and %
24
A/F sensor 1 output voltage and short term fuel trim associated with A/F sensor 1
V and %
1C
On-board diagnosis system
NOTE:
Refer to OBD-II general scan tool manufacturer's instruction manual to access generic OBD-II PIDs (MODE
$01).
EN(DOHC TURBO)-34
OBD-II GENERAL SCAN TOOL
Engine (Diagnostics)
3. MODE $02 (POWERTRAIN FREEZE FRAME DATA) S08852
Refers to data denoting the operating condition when trouble is sensed by the on-board diagnosis system. A list of the support data and PID (Parameter Identification) codes are shown in the following table.
PID
Data
Unit of measure
02
Trouble code that caused CARB required freeze frame data storage
03
Fuel system control status
04
Calculated engine load value
%
05
Engine coolant temperature
°C
06
Short term fuel trim
%
07
Long term fuel trim
%
0B
Intake manifold absolute pressure
kPa
??
Engine revolution
rpm
0D
Vehicle speed
km/h
NOTE:
Refer to OBD-II general scan tool manufacturer's instruction manual to access freeze frame data (MODE
$02).
4.   MODE $03 (EMISSION-RELATED POWERTRAIN DIAGNOSTIC TROUBLE CODE) a»*™*
Refer to Read Diagnostic Trouble Code for information about data denoting emission-related powertrain diagnostic trouble codes. <Ref. to EN(DOHC TURBO)-43, Read Diagnostic Trouble Code.>
5.   MODE $04 (CLEAR/RESET EMISSION-RELATED DIAGNOSTIC INFORMATION) S088527A1605
Refers to the mode used to clear or reset emission-related diagnostic information (OBD-II trouble diagnos­tic information).
NOTE:
Refer to OBD-II general scan tool manufacturer's instruction manual to clear or reset emission-related
diagnostic information (MODE $04).
EN(DOHC TURBO)-35