|
|
|
|
|
|
|
|
|
|
Fuel Injection (Fuel Systems)
|
|
|
|
|
|
|
|
|
|
8) Disconnect two-way valve hose (A) from two-way valve and disconnect canister hose (B) from canister.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
WARNING:
• Place "NO FIRE" signs near the working area.
• Be careful not to spill fuel on the floor.
1) Set vehicle on the lift.
2) Release fuel pressure. <Ref. to FU(DOHC TURBO)-52, RELEASING OF FUEL PRESSURE, OPERATION, Fuel.>
3) Drain fuel from fuel tank. <Ref. to FU(DOHC TURBO)-50, DRAINING FUEL, OPERATION, Fuel.>
4) Remove rear seat.
5) Disconnect connector of fuel tank cord to rear harness.
|
|
|
|
|
9) Loosen clamp and disconnect fuel filler hose (A) and air vent hose (B) from fuel filler pipe.
|
|
|
|
|
|
|
|
|
|
|
|
10) Move clips, and disconnect quick connector. <Ref. to FU(DOHC TURBO)-67, REMOVAL, Fuel Delivery, Return and Evaporation Lines.>
11) Disconnect fuel hoses.
|
|
|
|
6) Push grommet which holds fuel tank cord on floor panel into under the body.
|
|
|
|
|
|
|
|
|
|
|
|
7) Remove rear crossmember. <Ref. to RS-20, REMOVAL, Rear Crossmember.>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Fuel Injection (Fuel Systems)
|
|
|
|
|
|
|
|
12) Support fuel tank with transmission jack, remove bolts from bands and dismount fuel tank from the vehicle.
WARNING:
A helper is required to perform this work.
|
4) Connect fuel filler hose (A) and air vent hose (B).
|
|
|
|
|
|
|
|
|
|
|
|
5) Connect fuel hoses, and hold then with clips and quick connector. <Ref. to FU(DOHC TURBO)-68, INSTALLATION, Fuel Delivery, Return and Evaporation Lines.>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1) Support fuel tank with transmission jack and push fuel tank harness into access hole with grom-met.
2) Set fuel tank and temporarily tighten bolts of fuel tank bands.
WARNING:
A helper is required to perform this work.
|
|
|
|
|
|
|
|
6) Tighten band mounting bolts.
Tightening torque:
33 Nm (3.4 kgf-m, 25 ft-lb)
|
|
|
|
|
|
|
|
3) Connect two-way valve hose (A) to two-way valve and connect canister hose (B) to canister.
|
|
|
|
|
|
|
|
7) Install rear crossmember. <Ref. to RS-20, INSTALLATION, Rear Crossmember.>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Fuel Injection (Fuel Systems)
|
|
|
|
|
|
|
|
8) Connect connectors to fuel tank cord and plug service hole with grommet.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
9) Set rear seat and floor mat.
10) Connect connector to fuel pump relay.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1) Make sure there are no cracks, holes, or other damage on the fuel tank.
2) Make sure that the fuel hoses and fuel pipes are not cracked and that connections are tight.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
