|
|
|
|
|
|
|
|
|
|
Fuel Injection (Fuel Systems)
|
|
|
|
|
|
|
|
|
|
9) Move clip, and disconnect air vent hose from air vent pipe.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
WARNING:
• Place "No fire" signs near the working area.
• Be careful not to spill fuel on the floor.
1) Set the vehicle on the lift.
2) Drain fuel from fuel tank. <Ref. to FU(SOHCw/ oOBD)-41, RELEASING OF FUEL PRESSURE, OPERATION, Fuel.>
3) Remove screws holding packing in place.
4) Remove wheel nuts of rear right side.
5) Lift-up the vehicle.
6) Remove rear right side wheel.
|
|
|
|
10) Loosen clamp, and separate fuel filler hose (A) from fuel filler pipe.
11) Move clip, and separate air vent hose (B).
|
|
|
|
|
|
|
|
|
|
|
|
7) Remove fuel filler pipe protector.
|
|
|
|
|
|
|
|
|
12) Remove fuel filler pipe to under side of the vehicle.
|
|
|
|
|
|
|
|
8) Remove bolts which hold fuel filler pipe bracket on body.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Fuel Injection (Fuel Systems)
|
|
|
|
|
|
|
|
|
|
5) Insert air vent hose approximately 25 to 30 mm (0.98 to 1.18 in) into the lower end of air vent pipe and hold clip.
L = 27.5±2.5 mm (1.083±0.098 in)
|
|
|
|
1) Hold fuel filler flap open.
2) Set fuel saucer (A) with rubber packing (C), and insert fuel filler pipe into hole from the inner side of apron.
|
|
|
|
|
|
|
|
|
|
|
|
(1) Hose
(2) Clip
(3) Pipe
6) Tighten bolt which holds fuel filler pipe bracket on body.
Tightening torque:
22.6 Nm (2.3 kgf-m, 16.6 ft-lb)
|
|
|
|
3) Align holes in fuel filler pipe neck and set cup (B), and tighten screws.
NOTE:
If edges of rubber packing are folded toward the
inside, straighten it with a screwdriver.
|
|
|
|
|
|
|
|
|
|
|
|
4) Insert fuel filler hose (A) approximately 25 to 30 mm (0.98 to 1.18 in) over the lower end of fuel filler pipe and tighten clamp.
CAUTION:
Do not allow clips to touch air vent hose (B)
and rear suspension crossmember.
|
|
|
|
7) Connect air vent hose to air vent pipe.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Fuel Injection (Fuel Systems)
|
|
|
|
|
|
|
|
8) Install fuel filler pipe protector.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
9) Install rear right wheel.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
10) Lower the vehicle.
11) Tighten wheel nuts.
12) Connect connector to fuel pump relay. <Ref. to FU(SOHCw/oOBD)-40, INSTALLATION, Fuel Pump Relay.>
13) Connect battery ground terminal.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
