|
|
|
|
|
|
|
|
|
|
Fuel Injection (Fuel Systems)
|
|
|
|
|
|
|
|
|
|
(2) Remove bolts which hold power steering pipe brackets to intake manifold.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1) Release fuel pressure.
<Ref. to FU(SOHCw/oOBD)-41, RELEASING OF FUEL PRESSURE, OPERATION, Fuel.>
2) Open fuel flap lid, and remove fuel filler cap.
3) Disconnect battery ground cable.
|
|
|
|
|
|
|
|
(3) Remove bolts which secure power steering pump to bracket.
|
|
|
|
|
|
|
|
4) Remove air intake duct and air cleaner case. <Ref. to IN(SOHC)-8, REMOVAL, Air Intake Duct.> and <Ref. to IN(SOHC)-7, REMOVAL, Air Cleaner Case.>
5) Remove resonator chamber.
|
|
|
|
|
|
|
|
|
(4) Disconnect connector from power steering pump switch.
|
|
|
|
|
|
|
|
6) Remove spark plug cords from spark plugs (#1 and #3 cylinders).
|
|
|
|
|
|
|
|
|
(5) Place power steering pump and tank on the right side wheel apron.
|
|
|
|
|
|
|
|
7) Remove power steering pump and tank from brackets.
(1) Remove V-belt.
<Ref. to ME(SOHC)-42, REMOVAL, V-belt.>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Fuel Injection (Fuel Systems)
|
|
|
|
|
|
|
|
8) Disconnect connector from fuel injector.
|
3) Disconnect battery ground cable.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
9) Remove bolts (A) and (B) which install injector pipe to intake manifold.
|
4) Remove two bolts which install washer tank on body.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
10) Pull up injector pipe, and remove fuel injectors from intake manifold.
|
5) Disconnect connector from front window washer motor.
6) Disconnect connector from rear gate glass washer motor.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1) Release fuel pressure. <Ref. to FU(SOHCw/ oOBD)-41, RELEASING OF FUEL PRESSURE, OPERATION, Fuel.>
2) Open fuel flap lid, and remove fuel filler cap.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Fuel Injection (Fuel Systems)
|
|
|
|
|
|
|
|
7) Disconnect rear window glass washer hose from washer motor, then plug connection with a suitable cap.
8) Move washer tank, and secure it away from working area.
|
12) Remove bolt which holds fuel pipe on the left side intake manifold.
|
|
|
|
|
|
|
|
|
|
|
|
13) Pull up injector pipe, and remove fuel injectors from intake manifold.
|
|
|
|
|
|
|
|
9) Remove spark plug cords from spark plugs (#2 and #4 cylinders).
|
|
|
|
|
|
|
|
|
|
|
|
|
10) Disconnect connector from fuel injector.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
11) Remove bolt which installs injector pipe to intake manifold.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Fuel Injection (Fuel Systems)
|
|
|
|
|
|
|
|
|
2. LH SIDE S165051A1102
Install in the reverse order of removal.
NOTE:
Replace O-rings with new ones.
|
|
|
|
|
|
|
|
|
1. RH SIDE S165051A1101
Install in the reverse order of removal.
NOTE:
Replace O-rings with new ones.
|
|
|
|
|
|
|
|
|
|
|
|
|
(A) O-ring
(B) Insulator A
(C) Fuel injector
(D) Insulator B
Tightening torque:
4.9 Nm (0.50 kgf-m, 3.6 ft-lb)
|
|
|
|
(A) O-ring
(B) Insulator A
(C) Fuel injector
(D) Insulator B
Tightening torque:
Bolt (A) 4.9 Nm (0.50 kgf-m, 3.6 ft-lb) Bolt (B) 19 Nm (1.9 kgf-m, 13.7 ft-lb)
|
|
|
|
|
|
|
|
|
|
|
|
Tightening torque:
19 Nm (1.9 kgf-m, 13.7 ft-lb)
|
|
|
|
|
|
|
|
Tightening torque:
32 Nm (3.3 kgf-m, 23.9 ft-lb)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
