FRONT EXHAUST PIPE
|
|||||
|
|||||
Exhaust
|
|||||
|
|||||
|
6) Separate front and center exhaust pipe assemÂbly from rear exhaust pipe.
WARNING:
Be careful, exhaust pipe is hot.
|
||||
|
S152065
|
||||
2. Front Exhaust Pipe
A: REMOVAL S152065A18
1) Disconnect battery ground cable.
|
|||||
|
|||||
![]() |
![]() |
||||
|
|||||
2) Disconnect front oxygen (A/F) sensor connecÂtor.
|
7) Remove bolts which hold front exhaust pipe onto cylinder heads.
CAUTION:
Be careful not to pull down front and center
exhaust pipe assembly.
|
||||
![]() |
|||||
![]() |
|||||
3) Disconnect rear oxygen sensor connector.
|
|||||
![]() |
|||||
8) Remove bolt which installs front and center exhaust pipe assembly to hanger bracket.
|
|||||
![]() |
|||||
4) Lift-up the vehicle.
5) Remove undercover. <Ref. EI-11, REMOVAL, Front Under Cover.>
|
|||||
|
|||||
9) Remove front and center exhaust pipe assemÂbly from the vehicle.
CAUTION:
- Be careful not to let front and center exhaust pipe assembly fall off when removing as it is quite heavy.
- After removing front and center exhaust assembly, do not apply excessive pulling force on rear exhaust pipe.
|
|||||
|
|||||
EX(SOHC)-5
|
|||||
|
|||||
|
||||
FRONT EXHAUST PIPE
|
||||
|
||||
Exhaust
|
||||
|
||||
10) Separate front exhaust pipe from center exhaust pipe.
|
4) Tighten bolts which hold front exhaust pipe onto cylinder heads.
Tightening torque:
30 Nm (3.1 kgf-m, 22.4 ft-lb)
|
|||
![]() |
||||
![]() |
||||
B: INSTALLATION
|
S152065A11
|
|||
|
||||
1) Install front exhaust pipe to center exhaust pipe.
CAUTION:
Replace gaskets with new ones.
Tightening torque:
30 Nm (3.1 kgf-m, 22.4 ft-lb)
|
5) Tighten bolts which install front and center exhaust pipe assembly to rear exhaust pipe.
Tightening torque:
18 Nm (1.8 kgf-m, 13.0 ft-lb)
|
|||
![]() |
||||
![]() |
||||
6) Tighten bolt which holds front and center exhaust pipe assembly to hanger bracket.
Tightening torque:
35 Nm (3.6 kgf-m, 26.0 ft-lb)
|
||||
2) Install front and center exhaust pipe assembly to the vehicle.
3) Temporarily tighten bolt which installs front and center exhaust pipe assembly to hanger bracket.
|
||||
![]() |
||||
![]() |
||||
7) Install under cover. <Ref. EI-11, INSTALLATION, Front Under Cover.>
8) Lower the vehicle.
|
||||
|
||||
EX(SOHC)-6
|
||||
|
||||
|
|||
FRONT EXHAUST PIPE
|
|||
|
|||
Exhaust
|
|||
|
|||
9) Connect rear oxygen sensor connector.
|
|||
|
|||
![]() |
|||
|
|||
10) Connect front oxygen (A/F) sensor connector.
|
|||
|
|||
![]() |
|||
|
|||
11) Connect battery ground cable.
|
|||
|
|||
![]() |
|||
|
|||
C: INSPECTION
|
S152065A10
|
||
|
|||
1) Make sure there are no exhaust leaks from conÂnections and welds.
2) Make sure there are no holes or rusting.
|
|||
|
|||
EX(SOHC)-7
|
|||
|
|||
|