2001 СУБАРУ ФОРЕСТЕР. Руководство по обслуживанию

ENGINE OIL PRESSURE

Mechanical

6. Engine Oil Pressure

A: INSPECTION S153⁶

1) Disconnect battery ground cable.

S153655

7) Start the engine, and measure oil pressure.

Oil pressure:

98 kPa (1.0 kg/cm², 14 psi) or more at 800

rpm

294 kPa (3.0 kg/cm², 43 psi) or more at

5,000 rpm

CAUTION:

- If oil pressure is out of specification, check oil pump, oil filter and lubrication line. <Ref. to LU-25, INSPECTION, Engine Lubrication SysВtem Trouble in General.>

- If oil pressure warning light is turned ON and oil pressure is in specification, replace oil presВsure switch. <Ref. to LU-25, INSPECTION, Engine Lubrication System Trouble in GenВeral. >

NOTE:

The specified data is based on an engine oil temВperature of 80°C (176°F).

8) After measuring oil pressure, install oil pressure switch. <Ref. to LU-21, INSTALLATION, Oil PresВsure Switch. >

Tightening torque:

25 Nm (2.5 kgf-m, 18.1 ft-lb)

9) Install generator and V-belt in the reverse order of removal, and adjust the V-belt deflection. <Ref. to ME(SOHC)-42, INSTALLATION, V-belt.>

2) Remove generator from bracket.

(1) Loosen lock bolt and slider bolt, and remove front side V-belt. <Ref. to ME(SOHC)-42, REMOVAL, V-belt.>

(2) Remove generator lock bolt.

(3) Remove bolt which install generator on bracket.

3) Disconnect connector from oil pressure switch.

4) Remove oil pressure switch from engine cylinВder block. <Ref. to LU-21, REMOVAL, Oil Pressure Switch. >

5) Connect oil pressure gauge hose to cylinder block.

6) Connect battery ground cable.

ME(SOHC)-27



ENGINE OIL PRESSURE

Mechanical

6. Engine Oil Pressure A: INSPECTION S153⁶ 1) Disconnect battery ground cable.	S153655	7) Start the engine, and measure oil pressure.
	S153655

		*Oil pressure:* *98 kPa (1.0 kg/cm², 14 psi) or more at 800* *rpm* *294 kPa (3.0 kg/cm², 43 psi) or more at* *5,000 rpm* CAUTION: - If oil pressure is out of specification, check oil pump, oil filter and lubrication line. <Ref. to LU-25, INSPECTION, Engine Lubrication SysВtem Trouble in General.> - If oil pressure warning light is turned ON and oil pressure is in specification, replace oil presВsure switch. <Ref. to LU-25, INSPECTION, Engine Lubrication System Trouble in GenВeral. > NOTE: The specified data is based on an engine oil temВperature of 80°C (176°F). 8) After measuring oil pressure, install oil pressure switch. <Ref. to LU-21, INSTALLATION, Oil PresВsure Switch. > *Tightening torque:* *25 Nm (2.5 kgf-m, 18.1 ft-lb)* 9) Install generator and V-belt in the reverse order of removal, and adjust the V-belt deflection. <Ref. to ME(SOHC)-42, INSTALLATION, V-belt.>
2) Remove generator from bracket. (1) Loosen lock bolt and slider bolt, and remove front side V-belt. <Ref. to ME(SOHC)-42, REMOVAL, V-belt.> (2) Remove generator lock bolt. (3) Remove bolt which install generator on bracket.

3) Disconnect connector from oil pressure switch. 4) Remove oil pressure switch from engine cylinВder block. <Ref. to LU-21, REMOVAL, Oil Pressure Switch. > 5) Connect oil pressure gauge hose to cylinder block. 6) Connect battery ground cable.



ME(SOHC)-27